Railblaza Tracport Dash

Railblaza Authorized Dealer.
Full Manufacturer Warranty.

Railblaza

$ 83.95

Size

Quantity

info

Best price online audited bynetRivals

lupa

Railblaza Tracport Dash

close

Railblaza Tracport Dash

Railblaza Tracport Dash

Railblaza Tracport Dash

Railblaza Tracport Dash

play-video

Railblaza Tracport Dash

Product description

Product description

Strength and convenience, married in a 500 mm rail equipped with 4 StarPorts and two StarPort adapters for mounting.

Put your own RAILBLAZA accessories together in a convenient, lightweight system...

Then remove the system when youre finished for security, transport or storage!

The TracPort Dash 500 comes with 4 StarPorts, 2 StarPort adapters, infill extrusion and all fastenings needed to install and trim the rail.


Specifications:

- TracPort Dash 500: 500mm extrusion,
- 2 x endcaps,
- 4 x Starport/TracNut Combos,
- Infill cut to length,
- 2 x StarPort Adapters,
- all fastenings.
- Extrusion - Anodised Aluminium
- StarPort AES - (Acrylonitrile Ethylene Styrene)
- Accessories: 15% glass-filled nylon

Construction Materials:
- Extrusion ? Anodised aluminium
- StarPort ? UV stabilised AES plastic
- Locking Slide ? UV stabilised PC plastic
- TracNut ? UV stabilised fibreglass reinforced nylon plastic
- Gasket ? UV stabilised TPE Rubber
- Stainless steel fasteners


Mounting Instructions:

Required Tools:

- Tape Measure or Rule
- Number 3 phillips Screwdriver
- If mounting centers are other than 100mm (4″) you will also require;
- Number 2 pozidrive screwdriver
- Center punch
- 6.5mm (1/4″) drill bit
- Coutersink bit (optional)

Before installing:
The TracPort Dash 500 requires 2 StarPorts pre-fitted to the surface or rail it will be mounted on, if these StarPorts are at 100mm (4″) centers the pre-drilled mounting holes on the TracPort Dash 500 can be used.

Drilling holes in TracPort [A]:
If the StarPorts on your vessel are not at 100mm (4″) centers you will need to drill new mounting holes for the adaptors. Remove endcap screws and take off the endcap [B] from one end, then loosen the screws on the front of the StarPorts and remove enough StarPorts [C] to give access to the TracPort surface, mark and centre punch new drilling points at the same centers as your StarPorts. Using a 6.5mm (1/4″) drill bit, drill through the TracPort, then countersink the holes on the inside, ready for the countersunk screw head.

Fitting the adaptors [D]:
The two supplied adaptors come with nuts inserted. Thread the plastic washers onto the screws before inserting bolts through the TracPort and screwing loosely into the adaptors. Place the adaptors into your StarPorts, and then tighten the screws using the phillips screwdriver.

Fitting the optional Infill Extrusion [E] The TracPort infill strip is used to trim the extrusion and reduce fouling. Once your accessories have been mounted, use a sharp knife, scissors or a guillotine to cut strips of infill to length and press them firmly into the extrusion from the front, not slide in from the end.

Railblaza Tracport Dash is available with different characteristics. Buy it at waveinn and benefit from all the advantages. In addition, Railblaza Tracport Dash has the official guarantee of the brand Railblaza. Also, you can complement your order with other product from our Vehicles and motors catalogue and Kayaks accessories category.

Features

. Vehicles and motors

Use the chart below to determine your size. If you´re on the borderline between two sizes, order the smaller size for a tighter fit or the larger size for a looser fit. If your measurements for bust and waist correspond to two different suggested sizes, order the size indicated by your bust measurement.

Customer reviews and questions (0)

Product rating 5 / 5
Write a review or ask our dedicated team of experts a question
coinn

Write a review about this product and earn CoINNs

(existing customers only)

Product rating:

Wrong code

Note: Your reviews will be reviewed by our staff and posted within five working days. Your question will be answered by email, so please make sure your email address is correct.

I accept your Privacy Policy

Customers who viewed Railblaza Tracport Dash, also viewed:

 
Railblaza Starport Adaptor

Railblaza

Starport Adaptor

$ 10.21 $ 7.95

 
Railblaza Rod Holder II

Railblaza

Rod Holder II

$ 28.12 $ 23.45

 
 
Railblaza Eye 25

Railblaza

Eye 25

$ 8.33 $ 6.95

imagen

Railblaza Tracport Dash

$ 83.95

Size

We guarantee the lowest online price!