Victron Energy Skylla-i 24/100 Charger

Features:

- Skylla-i (1+1): two outputs to charge 2 battery banks: The Skyllai (1+1) features 2 isolated outputs. The second output, limited to approximately 4 A and with a slightly lower output voltage, is intended to top up a starter battery.
- Skylla-i (3): three full current outputs to charge 3 battery banks: The Skylla-i (3) features 3 isolated outputs. All outputs can supply the full rated output current.
- Rugged: Aluminium epoxy powder coated cases with drip shield and stainless steel fixings withstand the rigors of an adverse environment: heat, humidity and salt air.Circuit boards are protected with an acrylic coating for maximum corrosion resistance. Temperature sensors ensure that power components will always operate within specified limits, if needed by automatic reduction of output current under extreme environmental conditions.
- Flexible: Next to a CAN bus (NMEA2000) interface, a rotary switch, DIP switches and potentiometers are available to adapt the charge algorithm to a particular battery and its conditions of use. Please refer to the manual for a complete overview of the possibilities.

Important features:
- Synchronised parallel operation: Several chargers can be synchronised with the CAN bus interface. This is achieved by simply interconnecting the chargers with RJ45 UTP-cables. Please see the manual for details.
The right amount of charge for a lead -acid battery: variable absorption time: When only shallow discharges occur the absorption time is kept short in order to prevent overcharging of the battery. After a deep discharge the absorption time is automatically increased to make sure that the battery is completely recharged.
- Preventing damage due to excessive gassing: the BatterySafe mode: If, in order to quickly charge a battery, a high charge current in combination with a high absorption voltage has been chosen, the Skylla-i will prevent damage due to excessive gassing by automatically limiting the rate of voltage increase once the gassing voltage has been reached.
- Less maintenance and aging when the battery is not in use: the Storage mode: The storage mode kicks in whenever the battery has not been subjected to discharge during 24 hours. In the storage mode float voltage is reduced to 2,2 V/cell (26,4 V for 24 V battery) to minimise
gassing and corrosion of the positive plates. Once a week the voltage is raised back to the absorption level to ‘refresh’ the battery. This feature prevents stratification of the electrolyte and sulphation, a major cause of early battery failure.
- To increase battery life: temperature compensation: Every Skylla-i comes with a battery temperature sensor. When connected, charge voltage will automatically decrease with increasing battery temperature. This feature is especially recommended for sealed lead- acid batteries and/or when important fluctuations of battery temperature are expected.
- Battery voltage sense: In order to compensate for voltage loss due to cable resistance, the Skylla-i isprovided with a voltage sense facility so that the battery always receives the correct charge voltage.
- Suitable for AC and DC supply (AC-DC and DC-DC operation): The chargers also accept a DC supply
- Use as a power supply: As a result of the perfectly stabilized output voltage, the Skylla-i can be used as a power supply if batteries or large buffer capacitors are not available.
- Li-Ion (LiFePO4) ready: Simple charger on-off control can be implemented by connecting a relay or open collector optocoupleroutput from a
Li-Ion BMS to the remote control port of the charger. Alternatively complete control of voltage and current can be achieved by connecting to the galvanically isolated CAN bus port.


Specifications:

- Input voltage (VAC): 230V
- Input voltage range (VAC): 185-265 V
- Input voltage range (VDC): 180-350 V
- Maximum AC input current @ 180 VAC: 20 A
- Frequency(Hz): 45-65 Hz
- Power factor: 0,98
- Charge voltage absorption (VDC)(1): 28,8 V
- Charge voltage float (VDC): 27,6 V
- Charge voltage ‘storage’ (VDC): 26,4 V
- Charge current (A)(2): 100 A
- Charge current starter batt. (A): 4
- Charge algorithm: 7 stage adaptive
- Battery capacity (Ah): 500-1000 Ah
- Charge algorithm, Li-Ion: 3 stage, with on-off control or CAN bus control
- Temperature sensor: Yes
- Can be used as power supply: Yes
- Remote on-off port: Yes (can be connected to a Li-Ion BMS)
- CAN bus communication port(VE.Can): Two RJ45 connectors, NMEA2000 protocol, galvanically isolated
- Synchronised parallel operation: Yes, with VE.Can
- Alarm relay: DPST AC rating: 240VAC/4A DC rating: 4A up to 35VDC, 1A up to 60VDC
- Forced cooling: Yes
Protection:
- Battery reverse polarity (fuse)
- Output short circuit
- Over temperature
- Operating temp.range: 20 to 60°C (Full output current up to 40°C)
- Humidity (non-condensing): max 95%
- Material: aluminium
- Battery-connection: M8 bolts
- 230 VAC-connection: screw-clamp 10mm² (AWG 7)
- Protection category: IP 21
- Weight kg (lbs): 7 kg (16 lbs)
- Dimensions hxwxd in mm: 405 x 250 x 150 mm(16.0 x 9.9 x 5.9 inch)

Victron energy Skylla-i 24/100 Charger has the official guarantee from the brand Victron energy. Buying in our online nautical and fishing store, you will have Victron energy Skylla-i 24/100 Charger at home in a few days. At this moment the product is in stock and the price is 0 $. Don´t miss this opportunity!